Hi everyone,
I’m not sure if this is the right community, but the home networking magazines seem to be pretty dead. I’m a bit green with regard to networking, and am looking for help to see if the plan I’ve come up with will work.
The main image in the post is my current network setup. Basically the ISP modem/router is just a pass through and the 10 Gb port is connected to my Asus router, which has the DHCP server activated. All of my devices, home lab and smart home devices are connected to the Asus router via either Wifi or Ethernet. This works well, but I have many neighbours close by, and with my 30+ wifi devices, I think things aren’t working as well as they could be. I guess you could say one of my main motivations to start messing with this is to clean it up and move all possible devices to Ethernet.
The planned new setup is as follows, but I’m not sure if it’s even possible to function this way.
https://i.postimg.cc/7YftSFt6/IMG-9281.jpg
ISP modem/router > 2.5 Gb unmanaged switch > 2.5 Gb capable devices (NAS, hypervisor, PCs) will connect directly here, along with a 1 Gb managed switch to handle the DHCP > Asus router would connect to the managed switch to provide wifi, and remaining wired devices will all connect to the managed switch as well.
Any assistance would be appreciated! Thanks!
Edit: fixed second image url
You must log in or register to comment.
I would also consider to set up a DMZ for the Hypervisor and maybe NAS (depends on how you use it) if you access it from the internet.
The main issue is your 30+ Wi-Fi devices. One AP can only handle this much total bandwidth. But first, it looks like you waste 2gb of your fibre speed? Get a compatible router.
For your setup it almost looks like you’re better off with a total 10gb internal speed. And get 2 more AP, one dedicated for your smart home, one for „less important devices“ and use the ASUS for the rest. - remember to use different channels on each AP.
So in short hook your HV,NAS,PC,[new router w/ AP?],[AP2],[AP3],[AP1?] on a new 10GB switch. Split your devices over the 3 AP, on different channels
Edit: or you could get one of those for cheaper „Qnap QSW-M2108R-2C“ That is a 2.5G with two additional 10G ports so you could plug your new router into one of them and use the other for later use of the NAS if it supports that speed
proper access points support 30+ clients without any problem (I doubt that the advertised number of 300 clients holds up for unifi aps, but 30 is definitely not a problem), especially for low traffic clients like iot devices.
why op gives up 2gbps from his 3gbps line is a mystery to me though…
Is it necessary to dedicate a WAP to IoT, etc? I would recommend setting up separate SSIDs and connect each to their own VLAN, and each VLAN a subnet. And have each WaP broadcast each SSID and have the router handle the traffic routing. That way WAPs are dedicated to the devices that they are near, not the devices they are assigned to.
Since VLAN isn’t officially part of the standard, you’d need all your network devices support it. And I wanted to give a device-load-balance. So not increase coverage but reduce the amount of devices per AP. Separate SSIDs and VLAN aren’t helping that it just makes it easier to track, wich group is causing the load
Since VLAN isn’t officially part of the standard
VLANs are a standard: 802.1Q. Your client devices don’t have to support it, just your switches, routers, and access points. On a switch, you can configure each port to treat untagged data as part of a particular VLAN. Similarly, with a good wi-fi access point, you can add multiple SSIDs each of which is on a different VLAN.
You’re right. I just gave a very simplified answer. VLAN isn’t part of the default network communication and therefore every „node“ needs to support it and be correctly set up, or otherwise the VLAN tag will be removed at that point.
And in my other comment I emphasized, that my main issue with multiple WAP is, to distribute the amount of devices each has to talk to. Multi SSID wouldn’t solve that
